wire cutter pulse electric source

The paper analyzes and designs the main circuit of high-power IGBT inverted air plasma cutting power supply.

對一種大功率IGBT逆變式空氣等離子切割電源的主電路進行了原理分析與設計。

Focusing on characteristics of inverted plasma cutting power supply with nonlinearity,time variability and hybrid property,a simulation model of digital inverted cutting power system based on PI adjustment was put forward.

采用基于Simulink的元件仿真技術,針對逆變式等離子弧切割電源本身具有非線性、時變性及混雜性特點,建立了基于PI調節的數字化逆變式切割電源系統仿真模型。

Improvement of wire frame in HS-WEDM;

高速走絲電火花線切割機線架結構的改進

The software realization of serial communication for multi-WEDM machines;

電火花線切割機多機串行通訊軟件的開發

The development trend and applications about WEDM machine arc pointed out.

本文詳細分析總結了現有低速走絲電火花線切割機走絲系統的組成、功能及原理,在分析現狀的基礎上,指出了其應用及發展趨勢。

The high-frequency pulse waveform of WEDM pulse generator was analyzed. Basic condition method is presented the results is well.

分析了電火花線切割機脈沖電源的高頻脈沖波形，提出了有效的控制方法，獲得了良好的綜合效果。

Research on WEDM Pulse Power Supply Based on ISA Bus;

基于ISA的電火花線切割脈沖電源研究

Research on Improving the Main Control Circuit Based on the Pulse Power Supply of Electric Spark Line Cutting Machine

基于電火花線切割機床脈沖電源的主控電路改進研究

Research on Bidrectional Narrow Pulse Generator of Non-Resistance for WEDM;

往復走絲線切割窄脈寬無阻脈沖電源的研究

Research on Micro Energy and Controllable Pulse Power Supply for MWEDM;

微能可控微細電火花線切割脈沖電源的研究

Study on Energy-Saving Pulse Generator for WEDM;

電火花線切割加工節能脈沖電源的研究

DESIGN FOR INTERRUPT ACCESS OF DEVICE DRIVER OF NON-RESISTANCE PULSE GENERATOR FOR WIRE ELECTRICAL DISCHARGE MACHINING BASED ON WDM;

基于WDM的電火花線切割無阻脈沖電源中斷驅動程序設計

Research of Digital AC Voltage Controller Technology for LS-WEDM;

低速走絲線切割脈沖電源數字化交流調壓技術研究

The Study of Processing the Waste Water Emulsion of Linear Incision by the Method of Pulse Electroflocculation and Chemical Coagulation;

脈沖電絮凝法和化學混凝法處理線切割乳化液廢水的研究

The Study and Design on Pulse Standard Signal Generator for LSWEDM

慢走絲線切割機床脈沖基準信號發生器的研究與設計

The Study on Pulse Generator for LSWEDM

低速走絲線切割機床脈沖基準信號發生器的研究

NC EDM wire-cut machine

電火花數控線切割機床

NC wirecut EDM machine

數控電火花線切割機床

taper wire-cut EDM machine

錐度電火花線切割機床

super CNC wirecutting machine

電火花數控線切割機

The Design of Power Source of Linear Motor Based on Bilateral Pulse Variable Frequency Control;

雙向脈沖變頻控制直線電機電源的研究與設計

Study on the Control Technology of Isopulse with WEDM;

線切割加工中等能量脈沖控制技術的研究

Discuss on Multi-Times Cutting Technology of Move Back and Forth Run-Wire WEDM

往復走絲電火花線切割機床多次切割技術探討